Most A-pillar brackets are a single plate that gives you one place to bolt a light. The OMU Genesis Series A-Pillar Light System Mount for the Jeep Wrangler JK is two rows, and each row can be run or pulled on its own.
The bracket is machined from high-strength aluminum alloy and hard anodized. Mounting points line up with the factory A-pillar holes, so nothing is drilled or welded.
What It Fits
| Part | Fits | Does not fit |
|---|---|---|
| OMU Genesis Series A-Pillar Light System Mount For Jeep Wrangler JK | Jeep Wrangler JK | Jeep Wrangler JL, Gladiator JT, Ford Bronco |
It is the same part listed on our A-Pillar Light System Mount product page. If your vehicle is not in the row above, this one will not bolt up — message us before ordering and we will point you at the version that does.
Two Rows, Independent
The upper and lower light mounts each install and come off independently. For daily driving you can run the top row only and keep the truck visually clean. For a night trail run, both rows go back on.
The upper row carries a bidirectional sliding track, so you can move the lights up and down and dial the beam angle without pulling the bracket apart. Lights fasten with high-strength hardware that is meant to stay put on rough ground.
Machined Aluminum, Hard Anodized
The bracket is forged from high-strength aluminum alloy, precision machined and then hard anodized for a matte industrial finish. Cast or stamped brackets flex; a machined one holds its shape, which is what keeps your beam pattern pointed where you set it.
Vibration and Sightlines
Vibration-dampening pads sit at every contact point between the bracket and the body. That is what keeps a light bar from humming at highway speed and what protects the paint under the mounting feet.
The bracket is shaped to stay out of your windshield sightline. There is also a dedicated mount at the top for an action camera.
Installation
All mounting points align with the factory A-pillar holes. Remove the factory screws, align the bracket, tighten the bolts, mount your lights. No drilling and no welding, and the job runs about ten minutes with basic hand tools.
Because the bracket is pinned to factory holes rather than to an adhesive pad, it can come off again without leaving anything behind.
Specifications
| Fits | Jeep Wrangler JK |
|---|---|
| Material | High-strength aluminum alloy, hard anodized |
| Rows | Two, each installed or removed independently |
| Top row | Bidirectional sliding track for height and angle adjustment |
| Contact points | Vibration-dampening pads |
| Extras | Action camera mount at the top |
| Installation | Factory A-pillar holes, no drilling or welding, approx. 10 minutes |
| Price | $286.00 |
| Returns | 30 days |
Shipping and Returns
Orders ship from our warehouse at a flat $7.99 rate to US addresses. In-stock items leave the warehouse in 1–3 business days and typically arrive 5–10 business days after that. Custom and made-to-order items take longer, and we will confirm the lead time by email after you order.
Returns are accepted within 30 days of delivery. Email jenna@omu4x4.com first and we will send you the return address and the steps to follow.
Frequently Asked Questions
Does this fit the Wrangler JL or Gladiator JT?
No. This bracket is made for the Jeep Wrangler JK. We make separate A-pillar mounts for the JL and JT, and they are not interchangeable.
Do I need to drill the A-pillar?
No. The mounting points line up with the factory holes. Installation is remove, align, bolt, and takes around ten minutes with basic tools.
Can I run just one row of lights?
Yes. The upper and lower rows install and come off independently, so you can run the top row alone for daily driving.
Will the bracket rattle at speed?
Vibration-dampening pads are fitted at every contact point with the body, which is what keeps the bracket quiet and protects the paint under the feet.
Where to Go Next
Browse everything we make for the Jeep Wrangler JK, or see the full Genesis Series.